All posts by okuna291

Code test

 

/*
  Blink
  Turns on an LED on for one second, then off for one second, repeatedly.
 
  This example code is in the public domain.
 */
 
// Pin 13 has an LED connected on most Arduino boards.
// give it a name:
int led = 13;

// the setup routine runs once when you press reset:
void setup() {                
  // initialize the digital pin as an output.
  pinMode(led, OUTPUT);     
}

// the loop routine runs over and over again forever:
void loop() {
  digitalWrite(led, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(1000);               // wait for a second
  digitalWrite(led, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);               // wait for a second
}

/* Blink without Delay
 
 Turns on and off a light emitting diode(LED) connected to a digital  
 pin, without using the delay() function.  This means that other code
 can run at the same time without being interrupted by the LED code.
 
 The circuit:
 * LED attached from pin 13 to ground.
 * Note: on most Arduinos, there is already an LED on the board
 that's attached to pin 13, so no hardware is needed for this example.
 
 
 created 2005
 by David A. Mellis
 modified 8 Feb 2010
 by Paul Stoffregen
 
 This example code is in the public domain.

 
 http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay
 */

// constants won't change. Used here to 
// set pin numbers:
const int ledPin =  13;      // the number of the LED pin

// Variables will change:
int ledState = LOW;             // ledState used to set the LED
long previousMillis = 0;        // will store last time LED was updated

// the follow variables is a long because the time, measured in miliseconds,
// will quickly become a bigger number than can be stored in an int.
long interval = 1000;           // interval at which to blink (milliseconds)

void setup() {
  // set the digital pin as output:
  pinMode(ledPin, OUTPUT);      
}

void loop()
{
  // here is where you'd put code that needs to be running all the time.

  // check to see if it's time to blink the LED; that is, if the 
  // difference between the current time and last time you blinked 
  // the LED is bigger than the interval at which you want to 
  // blink the LED.
  unsigned long currentMillis = millis();
 
  if(currentMillis - previousMillis > interval) {
    // save the last time you blinked the LED 
    previousMillis = currentMillis;   

    // if the LED is off turn it on and vice-versa:
    if (ledState == LOW)
      ledState = HIGH;
    else
      ledState = LOW;

    // set the LED with the ledState of the variable:
    digitalWrite(ledPin, ledState);
  }
}

 


/* Blink without Delay
 
 Turns on and off a light emitting diode(LED) connected to a digital  
 pin, without using the delay() function.  This means that other code
 can run at the same time without being interrupted by the LED code.
 
 The circuit:
 * LED attached from pin 13 to ground.
 * Note: on most Arduinos, there is already an LED on the board
 that's attached to pin 13, so no hardware is needed for this example.
 
 
 created 2005
 by David A. Mellis
 modified 8 Feb 2010
 by Paul Stoffregen
 
 This example code is in the public domain.

 
 http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay
 */

// constants won't change. Used here to 
// set pin numbers:
const int ledPin =  13;      // the number of the LED pin

// Variables will change:
int ledState = LOW;             // ledState used to set the LED
long previousMillis = 0;        // will store last time LED was updated

// the follow variables is a long because the time, measured in miliseconds,
// will quickly become a bigger number than can be stored in an int.
long interval = 1000;           // interval at which to blink (milliseconds)

void setup() {
  // set the digital pin as output:
  pinMode(ledPin, OUTPUT);      
}

void loop()
{
  // here is where you'd put code that needs to be running all the time.

  // check to see if it's time to blink the LED; that is, if the 
  // difference between the current time and last time you blinked 
  // the LED is bigger than the interval at which you want to 
  // blink the LED.
  unsigned long currentMillis = millis();
 
  if(currentMillis - previousMillis > interval) {
    // save the last time you blinked the LED 
    previousMillis = currentMillis;   

    // if the LED is off turn it on and vice-versa:
    if (ledState == LOW)
      ledState = HIGH;
    else
      ledState = LOW;

    // set the LED with the ledState of the variable:
    digitalWrite(ledPin, ledState);
  }
}


 

/*
  Blink
  Turns on an LED on for one second, then off for one second, repeatedly.
 
  This example code is in the public domain.
 */

void setup() {                
  // initialize the digital pin as an output.
  // Pin 13 has an LED connected on most Arduino boards:
  pinMode(13, OUTPUT);     
}

void loop() {
  digitalWrite(13, HIGH);   // set the LED on
  delay(1000);              // wait for a second
  digitalWrite(13, LOW);    // set the LED off
  delay(1000);              // wait for a second
}


/*
  Blink
  Turns on an LED on for one second, then off for one second, repeatedly.
 
  This example code is in the public domain.
 */
 
// Pin 13 has an LED connected on most Arduino boards.
// give it a name:
int led = 13;

// the setup routine runs once when you press reset:
void setup() {                
  // initialize the digital pin as an output.
  pinMode(led, OUTPUT);     
}

// the loop routine runs over and over again forever:
void loop() {
  digitalWrite(led, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(1000);               // wait for a second
  digitalWrite(led, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);               // wait for a second
}

AYO-INTRODUCTION

ME

okunseinde-pic
My name is Ayodamola Tanimowo Okunseinde…. but you can call me Ayo. I will be the tutor for this class. As most of you probably know… I LOOOOOVVVEE all things P-Comp, so I am always excited to answer questions or solve code and physical aspects of projects. I am a 2nd year MFA DT student, a lover of airplane food, a hater of pandas… I have a background in fine art painting and philosophy. At Parsons I have been exploring Afrofuturism, Design Fiction / Science Fiction, Technoshamanism, Emergence / A.I., and Biology / ACI. My thesis will involve these domains in the investigation of temporal transmission of culture and identity. I will be sharing weekly inspirational p-comp projects on the blog.

HOURS
My office hours are as follows (on D12):
Mon 10am – 1pm
Wed 3:00pm – 3:50pm
Thur 3:00pm – 3:50pm
Fri 12:10 – 3:50pm

INSPIRATION Check these links out:
Cloud Piano by David Bowen http://www.dwbowen.com/cloud_piano_movie.html

Macarena Song on Dot Matrix Printer by Mididesaster http://vimeo.com/96985367

You can email me to set an official meeting, or just grab me any time you see me around. I am looking forward to working with you all.

//ayo